SydneyNews
  • News
  • Economy
  • Internet
  • The science
  • Society
  • Business
  • Crypt
One News Now – the latest news in the world
  • News
  • Economy
  • Internet
  • The science
  • Society
  • Business
  • Crypt

How to independently replace the wheel on the car: what to take into account

  • July 11, 2017

It would seem that it is difficult: unscrewed – changed – twisted – and you can go. But it is very simple to damage the car when replacing the wheel or injure yourself.

When replacing the wheel, the following actions and their order should be remembered: their order should be remembered:

1. The car needs to be put on the brake, turning on the transfer of the first speed, on the other hand, put anti -ceremonial stops under the wheels, which should be slightly knitted with a hammer to prevent the car during replacement.

2. The spare wheel must first be removed, put on the ground, so that it is at the same time “at hand” and would not hurt when removing the replaced wheel. The screws of the replaced wheel, you need to loosen before raising the car.

3. It is necessary to install the jack on the stand in order to avoid pressing the jack into the ground. It is better to install the jack at an insignificant angle to increase the area of ​​the support.

4. Raise the car with a jack to a sufficient height to remove the wheel. Unscrew the screws of the wheel mount (it is recommended to unscrew the last screw, the one at the top of the disk). Remove it (removing the wheel, in order to avoid injuries, the hands should not be between the wheel and the body or under the wheel). It is most convenient to hold the wheel with both hands on the sides just below the middle.

5. Put the spare wheel in the reverse order. It is recommended to be the first to make the upper fastener screw, then the rest. The cylinder key, as far as possible, twist the screws. To ensure the correct revision of the wheel, the screws should be spinning crosswise, and not in a circle.

6. We lower the car to the ground. We tighten the wheel mounts finally. We remove the entire used tool and belonging to the place.

7. It remains only to check the pressure in the installed tire, and, if necessary, using the pump, pump it to the size, nominal for your car.

8. Having checked the wheel nipple for tightness, we tighten its cap.

9. The wheel is replaced.

Good luck on the roads!

Share
Tweet
Pin it
Share
Share
You May Also Like
View Post

Scientists have found a black hole with a mass of 36 billion Suns

  • March 3, 2025
View Post

Ancient beaches discovered on Mars, confirming the presence of oceans

  • March 3, 2025
View Post

Chinese engineers create world’s first robot that can perform a front somersault

  • March 3, 2025
View Post

Distinctive features of roads in Spain: what you need to know

  • January 21, 2025
View Post

How competently picking up the defense of the crankcase for the motorcycle

  • January 17, 2025
View Post

Choosing a bathroom mosaic

  • January 16, 2025
View Post

Choosing the installation of the iron door

  • January 15, 2025
View Post

Is it necessary to call the tow truck so often: the features of the service

  • January 13, 2025
Featured Posts
  • Many consumers ask themselves the question: what will be the first car
    • December 27, 2024
  • Rolling into three end ropes: what is it
    • August 21, 2017
  • How to install a DVR in the car with your own hands
    • December 5, 2024
  • Features of ventilation systems
    • August 16, 2017
  • Types of suspended ceilings and their device
    • January 23, 2018
Recent Posts
  • The cryptocurrency market reacted nervously to US foreign policy.
    • March 3, 2025
  • Argentina’s President Miley said he did not promote the LIBRA cryptocurrency
    • March 3, 2025
  • How cryptocurrency has changed since Trump’s victory
    • March 3, 2025
One News Now – the latest news in the world
  • © One News Now – the1day.com, 2017-2024. All Right Reserved.

Input your search keywords and press Enter.